Industrial Grade High Strength Epoxy Adhesive 50 ML Cartridge W/ 2 TIPs Use Gun

• Popularity - 4545 views, 649.3 views per day, 7 days on eBay. Super high amount of views. 4 sold.
• Price - Avg: $0.00, Low: $0.00, High: $0.00. Best quality when compared to PicClick similar items.
• Seller - + items sold. 0% negative feedback. Great seller with very good positive feedback and over 50 ratings.

Technical Product Bulletin<br>AA-BOND 201 Industrial, Fast Cure, Two Part Epoxy Adhesive, Quick Drying 5g<br>Takes 2 hours to hold and harden.  Do not move after 4 minutes until it fully cures.<br>You have 4 minute work time which is the amount of time you have to apply the product before it begins to dry.  Must work fast.  ** Buy AA-BOND 28 if you need 1 hour work time.<br>Industrial grade bond to all substrates.  The only two substrates which exhibit a weak bond are rubber and plastics.<br>Comes with two mixing tips.  Simply remove cap, twist and dispense product through the mixing tip.<br>The mixing tip will not be usable if you stop dispensing for an hour.  Keep tip attached until next use at which time you can replace it.<br>This 50ML cartridge requires a standard 50 ML dispensing gun.  Not included<br>This product is odorless / solvent free<br>Product Description:<br>AA-BOND 201 is an exceptional epoxy formulation recommended for lower temperature or wet industrial bonding applications where<br>FAST CURING is required. This versatile two-part epoxy system contains no solvents, mixes easily at room temperature, and is<br>suitable for high performance structural bonding applications where the combination of very fast room temperature curing coupled with<br>low shrinkage and excellent mechanical and electrical properties is needed. It develops strong, tough bonds to metals, plastics, glass<br>and glass fabrics, hardboards and forestry products, ceramics, rubber, masonry materials, and other construction materials.<br>When fully cured, AA-BOND 201 is an excellent electrical insulator, and provides superior resistance to vapors and gases, water,<br>galvanic action, petroleum fuels, salt solutions, and many other organic and inorganic compounds.<br>AA-BOND 201 develops significant properties 1 hour after mixing. However, an extended cure of 4-6 hours at 25°C is required for<br>fully matured bonds.<br>PRODUCT DESCRIPTION:<br>Appearance<br>Hazy, light straw<br>Cure Type<br>Heat cure or Room Temperature<br>Benefits<br>·<br>Resistant to many organic/inorganics<br>·<br>Strong bond strength<br>·<br>Great electrical insulator<br>·<br>Durable<br>Mix Ratio by weight<br>100:93 / Resin:Hardener<br>Substrates<br>·<br>Metals<br>·<br>ceramics<br>·<br>glass<br>·<br>glass fabrics<br>·<br>wood leather<br>·<br>rigid plastics<br>·<br>marble<br>·<br>stone<br>·<br>rock<br>·<br>concrete<br>·<br>sheetrock<br>·<br>plaster<br>·<br>cement and tile<br>Operating Temperature<br>-60 to 110 °C<br>Typical Application<br>Anything requiring the unique properties this adhesive offers<br>THERMAL PROPERTIES:<br>Volume Resistivity<br>5.00e+11 ohm-cm<br>Dielectric Constant<br>4.8<br>Dielectric Strength<br>410kV/in<br>CTE, linear<br>33.3 µin/in-°F@ RT<br>Glass Transition Temp, Tg<br>25 °C,               77 °F<br>Minimum Service Temperature, Air<br>-60°C,              76°F<br>Maximum Service Temperature, Air<br>115°C,<br>302°F<br>GENERAL INFORMATION:<br>For safe handling information on this product, consult the<br>Material Safety Data Sheet, (MSDS).<br>HOW TO USE:<br>1<br>.<br>Carefully clean and dry all surfaces to be bonded.<br>2<br>.<br>Apply AA-BOND 201 completely mixed adhesive to the prepared surfaces, and gently press these surfaces together.<br>Contact pressure is adequate for strong, reliable bonds;<br>however, maintain contact until adhesive is completely<br>cured.<br>3<br>.<br>Some separation of components is common during<br>shipping and storage. For this reason, it is recommended<br>that the contents of the shipping<br>container be thor